Handle/blade: titanium and G10/CPM S35VN
Blade length: 9.5 cm
Weight: 200 grams

The **Rick Hinderer Fulltrack** is a large and tough EDC pocket knife, designed by Rick Hinderer himself. When you hold this knife you immediately notice the size of it. With a 9.5 cm blade and a full-size handle it is a relatively imposing knife, ready to be used.

 You could consider the Fulltrack to be the large successor of the Halftrack. We, however, believe it to be an exceptional knife on its own. Of course the design lines look similar, but the Fulltrack is also unique at the same time. The Fulltrack, for instance, has been enhanced with an internal stop-pin, while with the Halftrack the stop-pin was pressed into the blade. The Fulltrack is also enhanced with the Tri-Way-pivot system. This means that ball bearings are mounted to the knife, but that phosphor bronze and teflon washers are also included. As such you can switch whenever you want to.

 The best thing about the Rick Hinderer Fulltrack is, however, the remarkable backspacer. Because of a cut-out on the presentation side you can easily pop it out to make sure you can use the back as a screwdriver. By making clever use of the two sizes of allen keys you will not only immediately own the right tools to tighten the pivot and frame screws but also the pocket clip.

 Those additional washers for your knife are great, but on the road they will not come in handy when they are stored at home in your drawer. For that reason Rick Hinderer milled a pocket from the handle where you can store the washers. With the built-in backspacer screw-tool you can loosen the handle and take the knife apart to exchange the washers. Genius! If you ask us.

 The blade is made from CPM S35VN-steel. A premium type of powder steel, which means that the steel has a very fine structure. In between the flipper and the edge you can find a finger choil. With it you have more control over the blade during the more detailed tasks. There is also a thumb groove to make sure you can open the knife a little more subtly. You open the blade with the flipper. When opened the blade is locked by a framelock.

 The handle is made from titanium. Both sides of the frame are enhanced with G10 inlays. These offer you additional grip and contrast. On the lockside the G10 also ensures that the framelock cannot be overstretched. As a result you are left with a lock that will work perfectly for years.

 Hinderer didn't hold back in terms of finishes on this Fulltrack. This is namely the special Gold DLC version. The frame and blade are enhanced with a gold-coloured coating, and the blade received a nice two-tone finish. You don't see them like this that often.

 All in all the Rick Hinderer Fulltrack is an amazing knife. Ready for everyone who appreciates a bigger-sized knife. Solidly constructed and well-thought out. Exactly what you expect from a Hinderer

.

Rick Hinderer Fulltrack Spanto S35VN Two Tone, DLC Gold Edition, OD Green G10 pocket knife

brand

colour

zm_series

handedness

blade_finish

opening_system

handle_material

knife_edge_type

multitool_tools

sharpening_type

knife_bladeshape

pocketknife_lock

sharpening_angle

pocketknife_steel

pocketknife_onehanded

value_multitool_tools_number

notforsale

knife_sheath

value_weight

value_blade_height

value_blade_length

value_opened_length

value_blade_thickness

not_replaced_in

expectedRestockDate

legal_agecheck_key

designer

engravable

Personalize it! We can engrave many products. Great as a gift! [Read more about the options here](/en/pt/-order-with-engraving.htm). Looking for an engraving? Don't forget to add the product '[Order with engraving](/en/pt/-order-with-engraving.htm)' to your order. 

Can be engraved

warranty

Almost all the products we sell come with a manufacturing warranty. Want to learn more about the warranty? Read our topic: [warranty explained](/en/ct/warranty-explained.htm)

Warranty

origin

The country of origin is the country the product is produced, as far as we know. This may differ from the country where the brand itself is located.

Country of origin

article_number_site

General information

We always measure the blade height at the highest part of the blade.

Blade height

We always measure the blade length ourselves. This is the length of the blade from the tip to the front of the handle. This may deviate from the manufacturer's specification.

Blade length

value_blade_length_edge

The length of the cutting edge is measured from the tip to the start of the edge. This may deviate from the manufacturer's specification.

Cutting edge length

We always measure the blade thickness at the thickest part of the blade. Often just before the handle. This may deviate from the manufacturer's specification.

Blade thickness

value_closed_length

We always weigh a product as bare as possible. Knives and axes always without their sheath, lights (if possible) without their battery. For knife sets we measure the entire weight. This may deviate from the manufacturer's specifications.

Weight

Dimensions & weight

value_steel_hardness

The hardness in Rockwell C for a knife is always according to the manufacturer's specifications. When a manufacturer specifies a value of 56-58HRC, for instance, we always note the highest value, i.e. 58HRC.

Hardness

Material

bearring_type

The is the type of bearing used between the blade and the handle, as far as we were able to determine. [Want to learn more about bearing types](/en/ct/pocket-knife-bearings-compared.htm)?

Bearing type

This concerns the type of edge [Want to learn more about a serrated versus a plain edge](/en/ct/pocket-knives-difference-plain-edge-serrated.htm)?

Type of edge

molle_compatible

MOLLE is a mounting system that allows you to attach sheaths and other accessories to backpacks. With this specification we indicate whether a product is already MOLLE-compatible by default. [Want to learn more MOLLE](/en/ct/what-is-molle.htm)?

MOLLE-compatible

pocket_blade_type

pocketknife_clip

pocketknife_clip_position

pocketknife_clip_side

This is the type of lock used. There are many different types of locks that are used by many different brands. [Want to learn more about locks](/en/ct/locking-mechanisms-on-pocket-knives.htm)?

Lock

We measure the sharpening angle ourselves. This value is the angle per side.  So 20º means that the total angle of the edge is 40º. Please note that knives are almost always sharpened by hand, even in factories. This value is therefore only an indication of a single tool measured by us. You are always free to choose your own sharpening angle. [Learn more about sharpening angles](/en/ct/sharpening-angles-explained.htm).

Sharpening angle

In terms of grind we are talking about how the complete blade thickness extends into the edge. Want to learn more about grinds? [Read all about grinds on knives](/en/ct/knife-grinds.htm).

Rick Hinderer Fulltrack Spanto S35VN Two Tone, DLC Gold Edition, OD Green G10 pocket knife